Bolt on Brackets for Wood Docks
Our heavy duty dock hardware is made using 1/4" steel. All dock hardware is made for 1/2" carriage bolts and is hot dipped galvanized after fabrication. Our hardware can be used with up to 4" thick lumber. Need some help knowing where everything goes? Our experienced staff can help. Call 1-800-585-6890
View as:
List
Sort by:
Default 
Galvanized Finger Stabilizer/Tie Bar
CODE: Y126-H-FSP
Use these when you have one dock section connected to another dock section at a 90 degree angle to spread out the load on the hinge points. For example: If you have a 4' x 20' finger hinged to a 8' wide main dock you can use these on both sides of the 4' finger to make the...[more]
Inside Corner
CODE: Y126-WH-IC
(Y126-WH-IC) The inside corner, working opposite the outside corner, sandwiches the wood, keeping bolts from burying themselves in the wood. This corner gusset will give the dock a lot of strength and stability.
Outside Corner End
CODE: Y126-WH-OCE
(Y126-WH-OCE) The outside corner end is used at the ends of dock, ends of fingers, or corners of swim platforms.
Outside Corner Female
CODE: Y126-WH-OCF
(Y126-WH-OCF) The Outside Corner Female has two 1/2" tabs with holes for a 3/4" Connector Pin (Y126-B-PIN) . Use with an Outside Corner Male (Y126-WH-OCF) or with a Single "T" Male (Y126-WH-SF) at the corner of your dock to attach a finger or dock section. [more]
Outside Corner Male
CODE: Y126-WH-OCM
(Y126-WH-OCM) The Outside Corner Male has one 5/8" tab with a hole for a 3/4" Connector Pin (Y126-B-PIN) . Use with an Outside Corner Female (Y126-WH-OCF) or with a Single "T" Female (Y126-WH-SF) at the corner of your dock to attach a finger or dock section. [more]
Outside Corner Female - Male
CODE: Y126-WH-OCFM
Female/Male Outside Corner Use 1/2” bolts for assembly.
Outside Corner Female - Female
CODE: Y126-WH-OCFF
Female/Female Outside Corner Use 1/2” bolts for assembly.
Dock Single "T" Female
CODE: Y126-WH-SF
(Y126-WH-SF) The Single "T" Female has two 1/2" tabs with holes for a 3/4" Connector Pin (Y126-B-PIN) and is used with a Single "T" Male (Y126-WH-SM) or Outside Corner Male (Y126-WH-OCM) . The male and female singles can both be used to make finger attachments by...[more]
Dock Single "T" Male
CODE: Y126-WH-SM
(Y126-WH-SM) The Single "T" Male has one 5/8" tab with a hole for a 3/4" Connector Pin (Y126-B-PIN) and is used with a Single "T" Female (Y126-WH-SF) or Outside Corner Female (Y126-WH-OCF) . The male and female singles can both be used to make finger attachments by...[more]
Dock Backup Plate
CODE: Y126-WH-B
(Y126-WH-B) Use the Backup Plate with our Single "T" Males (Y126-WH-SM) and Single "T" Females (Y126-WH-SF) for additional strength. They also keep the bolts from pulling through your wood. [more]
Dock Chain Retainer
CODE: Y126-WH-CRS
(Y126-WH-CRS) Our Chain Retainer bolts to the side of your dock and uses chain to hold the dock in place. You can use 5/16", 3/8" or 1/2"chain. Use either (2) Y126-WH-W washer plates or (1) Y126-WH-B back up plate. 5" L x 5" H. [more]
3/4" x 3 1/2" Bent Pull Pin
CODE: Y126-F-3435-B
3/4" Connector Pin (Y126-B-PIN) . Use with an Outside Corner Female (Y126-WH-OCF) and (Y126-WH-OCM) The Outside Corner Male and Outside Corner Female has 5/8" tabs or with a Single "T" Female (Y126-WH-SF) at the corner of your dock to attach a finger or dock...[more]
Angle
CODE: Y126-WH-A
(Y126-WH-A) Angles are used with a Washer Plate (Y126-WH-W) to hold cross stringers to side stringers. These two pieces of steel sandwich the wood, creating a solid corner.
Washer Plate
CODE: Y126-WH-W
(Y126-WH-W) The washer plate is used primarily with Angles (Y126-WH-A) and Cleat Angles (Y126-WH-CA) . The plate has two square holes to keep the carriage bolts from turning when tightening them. [more]
Cleat Angle
CODE: Y126-WH-CA
(Y126-WH-CA) The cleat angle has slots that accommodate various cleat sizes. Bolt the cleat angle to the side stringer using a Washer Plate (Y126-WH-W) . Then bolt the cleat through the deck into the cleat angle. This will ensure that the cleat will not pull out of the deck. [more]
Splice Plate (set of 2)
CODE: Y126-WH-SP
(Y126-WH-SP) Our Splice Plates were designed to join two timbers together. One is used on each side. The bolt holes are drilled so that an angle and 1/ 1/2" lumber can be added at the splice and end up at the end of the splice. Our Splice Plates are sold in pairs. [more]
Categories
Cart is empty
